Gas fireplace service
Sweep & inspection
Caps & crowns
Flue relining
Masonry repairLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Why Chico Homeowners Choose Gelco Chimney Cleaning
We provide independent Gelco chimney cleaning service in Chico, and what sets our Gelco work apart is that we treat the insert, the flue, and the factory-built chimney as one system rather than three separate chores. If you own a Gelco insert or factory-built fireplace, you already know the brand rewards careful use. Our job is to keep it clean, safe, and burning the way it was designed to. We are an independent service provider with no affiliation to or authorization from Gelco, and we say so plainly. Our technicians have up to 8 years of experience, we document what we find, and we work from manufacturer specs. Call (844) 320-4731 to book a sweep in Chico.
Why Trust Chimney Sweep Chico for Your Gelco Chimney Cleaning?
Gelco equipment shows up across Chico, from older Craftman-era homes near downtown to newer builds on the north and east sides, and our technicians have pulled enough of these units apart to recognize the patterns. We know where a Gelco insert tends to glaze up first, which corners of the faceplate trap soot, and when a bad draft is really a gasket problem wearing a disguise. That familiarity is what separates a real Gelco service from a generic sweep that runs the same brush through every flue it meets.
We use quality parts that fit Gelco equipment correctly, and we stop short of calling them genuine or OEM. For door gaskets, glass, and baffle hardware we lean toward original manufacturer parts because the fit matters, and we’ll tell you when an aftermarket piece is a fine substitute and when it isn’t. Our work is warranty-safe: we don’t drill, cut, or modify Gelco equipment in ways that would give a manufacturer grounds to deny a claim, and we keep documentation on file. If something we touch ever comes into question, you’ll have a record behind it.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Common Gelco Chimney Cleaning Problems We Fix in Chico
Chico’s long burn season, roughly November through March, puts real hours on a Gelco insert. Here are the issues we see most often, why they happen, and what a proper service looks like.
- Glazed creosote on the baffle and secondary-air tubes. Gelco inserts have a shallow firebox and tight baffle clearances, so glazed creosote builds up there faster than owners expect. It’s often mistaken for ordinary soot and left alone, but glaze is hard, shiny, and stubbornly stuck, and it doesn’t sweep away with a quick pass. We use poly brushes and a creosote conditioner to break it down without scarring the baffle.
- Soot and ash behind the surround panel and convection grilles. Gelco insert surround panels and convection grilles trap ash and soot between the faceplate and the firebox, which restricts airflow and can leave heat discoloration on the surround. A regular sweep that skips behind the faceplate won’t catch this. We pull it apart, clean it out, and check the grilles for airflow once everything is back together.
- Degraded gaskets and door glass. Door gaskets and glass on Gelco inserts wear down between Chico’s hot, dry summers and cold, damp winters. A gasket that’s lost its seal lets air leak in, and the unit then burns hot and fast with poor control. Replacing a worn gasket is a small job that fixes a big behavior problem.
- Rusted chase covers and water intrusion at the top plate. Factory-built Gelco chimney sections have sealant at the top plate and flashing that ages out over time. Once water gets in, it rusts the firebox and rots the chase cover. We inspect the top of the system as closely as the bottom, because the leak up there is what ruins the appliance down here.
- Orphaned stacks and interior chimneys without modern liners. Around the older avenues near downtown Chico, it’s common to find masonry stacks left behind after a furnace upgrade, and interior chimneys from that era that never had a liner installed. These can leak creosote odors into living spaces and need relining before they’re safe to burn again. That’s where our HeatShield resurfacing work and DuraFlex flexible liners come in.
Gelco Parts & Our Repair-vs-Replace Approach
Our starting principle is simple: put the right part on the unit, not the cheapest one that bolts up. For Gelco inserts and fireplaces we prefer original manufacturer parts where they’re still available, particularly for door gaskets, glass, and baffle hardware, since fit and heat tolerance matter on those pieces. When an OEM fit has been discontinued, quality aftermarket caps and chase covers do the job well, and we’ll say so clearly. We don’t claim to stock genuine or OEM parts, and we don’t pretend to.
Repair versus replace comes down to the firebox and the liner. If either is cracked or spalling past safe repair, the honest answer is replacement, not a cosmetic patch that buys you a season and fails the next. We document the condition with photos so you can see what we see. If you’re weighing the call on a Gelco unit in Chico, call us and we’ll give you a plain answer.
Our Gelco Service Process – Step by Step
- 1
Diagnose by symptom and by eye. We start with what you’re telling us: smoke rolling out, weak draft, uneven heat. Then we perform a Level 2 inspection, camera and all, and look directly at the baffle, the tubes, the gasket, the surround, and the top of the chimney.
- 2
Repair or install. That means creosote removal with the right brushes and conditioner, a gasket or glass swap on the insert door, or relining with HeatShield or DuraFlex when the original flue won’t pass. Every material gets documented.
- 3
Test. We check draft, airflow, and door seal after the work, and we confirm the insert is venting the way it should before we call it done.
- 4
Record. You get the findings, the parts used, and the photos, which serves you well for insurance and warranty purposes down the line.
See the difference
Before
After
Before
After
Before
AfterGelco Products We Service & Install in Chico
Our Gelco service covers the wood-burning and gas equipment owners actually run in Chico. That includes Gelco wood-burning fireplace inserts, factory-built wood fireplaces, gas fireplace inserts, and freestanding wood stoves. For each one we handle three things: chimney sweeping, structural repair, and formal inspection. We install fitted caps and chase covers, replace gaskets and glass, address baffle and firebox hardware, and reline flues that need it. If you’re not sure whether your unit falls into our scope, call (844) 320-4731 and describe it. We’ll tell you straight whether we can help.
We Also Service These Brands
Gelco is one brand among several we work with regularly. We also install and service DuraFlex flexible liner systems, which handle offset and hard-to-reach flues that rigid liners can’t reach, and HeatShield, the resurfacing product we use to restore damaged flue tile without a full tear-out. If your chimney has a mix of brands from past work, we can work with that. One provider, start to finish.
FAQs – Gelco Chimney Cleaning Service in Chico
No. We are an independent service provider and are not authorized, certified, or affiliated with Gelco in any way. We service Gelco equipment because we know it well, not because the manufacturer has endorsed us. If you need manufacturer-authorized warranty work, contact Gelco directly. For routine cleaning and repair, we’re here to help.
Yes. We use original manufacturer parts where they’re available and quality aftermarket parts where the OEM fit has been discontinued. We don’t claim to stock genuine or OEM parts, and we tell you what’s going on the unit before we install it. Call (844) 320-4731 with your model information and we’ll confirm fit.
Most Gelco insert services run a few hours, though it depends on what we find. A standard sweep and inspection on a well-maintained insert is quicker than one that needs creosote conditioner, a gasket swap, and relining. We’ll give you a realistic estimate before we start. Call (844) 320-4731 to book.
We service Gelco wood-burning fireplace inserts, factory-built wood fireplaces, gas fireplace inserts, and freestanding wood stoves. For each one we handle sweeping, structural repair, and inspection. If your unit isn’t on this list, call (844) 320-4731 and we’ll tell you whether we can help.
Proper service performed to manufacturer specs should not void a Gelco warranty, and we work carefully to keep it that way. We don’t modify or alter equipment in ways a manufacturer would flag, and we document what we do. That said, we can’t speak for Gelco’s warranty terms, so check your documentation if you’re concerned. Call (844) 320-4731 with questions.
Cost depends on the service. A standard sweep and inspection is one amount, and creosote removal, gasket replacement, or relining adds to it based on what the unit actually needs. We set the price per job by a free written estimate, and you see the findings before we start. Call (844) 320-4731 for your exact quote – estimates are free.
Smoke on a cold start usually points to a draft problem, and on Gelco inserts the two most common causes are glazed creosote on the baffle and a degraded door gasket that lets air in and throws off the burn. A Level 2 inspection will tell us which. Call (844) 320-4731 to get it checked.
Often yes, but not always where glazed creosote and surround grilles are involved. A shallow firebox with tight baffle clearance sometimes needs the insert pulled for a proper cleaning behind the faceplate. We decide on site after inspection, and we tell you why before we do it.
Glazed, third-degree creosote is what we see most often, because Chico’s long burn season means frequent, hot fires that layer glaze on the baffle and secondary-air tubes. It’s hard to remove and needs a conditioner and the right brushes. Call (844) 320-4731 to schedule.
Usually yes. A rusted chase cover and aged sealant at the top plate are repairable before water reaches the firebox, and we install fitted caps and covers to keep it that way. If the rust has already gotten into the firebox, that changes the answer. Call (844) 320-4731 for an assessment.
No, gas inserts need different service than wood inserts. There’s no creosote to sweep, but gas units still need annual inspection for venting, glass condition, and the burner assembly, plus cleaning of dust and debris. We handle both kinds. Call (844) 320-4731 to book.
Book Your Gelco Service in Chico, CA
If you own a Gelco insert or fireplace in Chico and want it cleaned, inspected, or repaired properly, we’re ready to help. We document what we find, use quality parts that fit, and give you a written estimate before any work begins. Call (844) 320-4731. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Chimney Sweep Chico.