Chimney Repair in Chico, CA | Chimney Sweep Chico

Chimney Repair in Chico - Inspected on Camera, Then Priced in Writing

Liner and masonry work is where this trade gets a bad name, so nothing is quoted until you have seen the camera footage yourself. Then a written, itemized price with no scope creep.

Call to schedule your free estimate

Work is performed by our local vetted partner.

Free
Written Quotes
Licensed & Insured Written Quotes Free Estimates All Brands Satisfaction Guarantee

Work is performed by our local vetted partner.

Sweep & inspectionSweep & inspection
Caps & crownsCaps & crowns
Flue reliningFlue relining
Masonry repairMasonry repair
Gas fireplace serviceGas fireplace service
Every visit starts with

Level 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed

Worth knowing

Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.

Get your free estimate

Trusted Chimney Repair for Chico Homeowners

Chimney problems in Chico usually show up slowly: a crack in the crown, a rusted cap, mortar going soft in the heat, or flue tile that’s spalled from years of hot fires and cool-downs. Then the first rain of the season comes through and you find the stain on the ceiling. Our technicians have up to 8 years of experience repairing exactly these issues, and we document what we find so you have written evidence before anyone picks up a tool. We work both burning season prep and mid-season failures, with same-day repair available in Chico when the schedule allows. Call (844) 320-4731 to book a free estimate.

Call (844) 320-4731

Chimney Cap Installation

Chimney Cap Installation is the fitting of a proper manufactured cap over the flue opening to keep rain, birds, squirrels and debris out while still letting smoke and gases escape. You need one if your chimney has no cap, has a homemade screen box rusted through, or has a cap that no longer fits the flue because the crown or tile has been repaired. We install fitted caps from Gelco and Famco rather than bending sheet metal on the roof. Most cap installations run in the $250-$600 range, and the written estimate sets the final price.

Why a Fitted Cap Matters More Than a Screen

A fitted cap is sized to your actual flue opening and anchored to the crown or flue tile, so wind doesn’t lift it and water doesn’t run around the edges. A loose screen box funnels rain straight into the flue. The difference shows up years later as cracked tile and rusted damper hardware.

Caps for Wood Stoves and Fireplaces

Wood stoves, open fireplaces and multi-flue chimneys each take a different cap style. We match the cap to the appliance and the flue count, not to whatever’s on the shelf. That means the cap still vents correctly through a hot burn without letting water in.

Explore

Styles & brands we work with

  • Sweep & inspection
  • Caps & crowns
  • Flue relining
  • Masonry repair
  • Gas fireplace service

Chimney Cap Replacement

Chimney Cap Replacement is swapping a failed, rusted or storm-damaged cap for a new manufactured unit that fits your flue correctly. Replace it when the old cap is rusted through, warped, missing its screen or animal mesh, or when a larger animal has pushed it out of position. We remove the old cap, inspect the flue tile top while we’re up there, and seat a new Gelco or Olympia Chimney cap. Cap replacement typically costs $200-$550 depending on flue configuration and cap style, with the written estimate setting the final price.

What Happens When a Cap Fails

A failed cap lets water run down the inside of the flue and lets animals build nests. Both shorten the life of the flue tile and make the next sweep harder. Replacing the cap early is cheaper than repairing what the water damages.

Choosing the Right Cap Size

We measure the flue opening, the tile thickness and the crown lip before ordering. A cap that’s slightly too small can blow off in a gust, and one that’s too large doesn’t seal. Getting the measurement right the first time saves a second trip.

Chimney Liner Installation

Chimney Liner Installation is fitting a new flue liner, either to replace damaged clay tile or to line a flue that never had one. You need it when the existing tile is cracked, spalled or offset, when the flue is unlined altogether, or when a new appliance needs a correctly sized flue. We install DuraFlex flexible liner systems, which allow correct installation in offset or hard-to-reach flues that rigid liners can’t handle. Liner installation usually runs $2,500-$6,500 depending on flue height, liner diameter and whether insulation is required, with the written estimate setting the final price.

Flexible Liners for Offset Flues

Chico homes often have flues that jog around a framing member or have a slight offset where the chimney passes through an upper floor. A flexible DuraFlex liner handles those bends where a rigid liner simply can’t be pushed through. The right liner for your flue is one that actually follows the flue, not one that gets cut short at the first offset.

Liner Resurfacing as an Alternative

When the tile is damaged but the flue structure is sound, HeatShield resurfacing can restore the liner without a full tear-out. We assess both options and show you the camera footage so you can see why one is the better call. Resurfacing isn’t right for every flue, and we’ll tell you when it isn’t.

Chimney Flashing Repair

Chimney Flashing Repair is fixing the metal and sealant that join the chimney to the roof, keeping water out of the roof deck and the attic. You need it when the flashing is lifting, the step flashing has pulled away from the shingles, or you see water stains on the ceiling or attic side of the chimney chase. We reseat and replace flashing, seal the joints and check the roof penetration on all sides. Flashing repair typically costs $350-$900 depending on roof access and the extent of the leak, with the written estimate setting the final price.

Where Leaks Usually Start

Most roof leaks near a chimney start at the top edge, where the backer flashing meets the shingles. Water wicks under a lifting edge and shows up inside weeks later. The camera inspection tells you where the leak is actually coming from.

Flashing and the Crown Together

Flashing and crown problems often look identical from inside the house. We inspect both before recommending work, so the repair addresses the leak instead of the symptom. Sometimes the flashing is fine and the crown is the whole story.

Chimney Crown Repair

Chimney Crown Repair is fixing the concrete cap on top of the chimney that sheds water away from the flue tile and masonry. You need it when the crown is cracked, crumbling, pulling away from the flue, or sloped the wrong way and holding water on top. We repair cracks and rebuild crowns that have failed, and we tie the new crown into the flashing and cap so water has somewhere to go. Crown repair usually runs $400-$1,200 depending on the size of the crown and how much masonry is affected, with the written estimate setting the final price.

Cracked Crowns and Water Damage

A cracked crown lets water into the masonry every time it rains, and masonry doesn’t dry out quickly once it’s wet. Over time that shows up as mortar loss and spalled brick. Catching a crack early keeps the repair small.

Crowns That Slope the Wrong Way

Some crowns were built flat or even slightly inverted, so water sits on top and works its way into the flue tile joints. We rebuild those with a proper slope away from the flue. The fix is straightforward and it saves the crown from coming back next year.

Chimney Repair Companies

Chimney Repair Companies vary widely in what they can actually do, and the gap matters most when a sweep report turns into a repair job. You need a repair company when you have documented damage that requires more than cleaning, and you need one that carries the products to fix it properly, not a general handyman. Chimney Sweep Chico handles sweeping, inspection and repair in one visit, so you aren’t chasing a separate contractor after the inspection. Repair costs depend on the scope, and the written estimate sets the final price.

What a Repair Visit Actually Covers

We start with a camera inspection of the flue and a look at the crown, flashing and cap. Then we write down what we found and give you the repair option that fits. If work can safely wait, we say so.

Manufacturer-Spec Materials

The brands we use, including DuraFlex, HeatShield, Gelco, Famco, Olympia Chimney and Copperfield, come with their own specifications for installation. Manufacturer-spec repair gives you a documented material trail for homeowner records and insurance purposes.

Chimney Masonry Repair

Chimney Masonry Repair is fixing the brick, mortar and stone that make up the chimney structure, from repointing joints to rebuilding sections that have lost their bond. You need it when mortar is soft or falling out, brick faces are spalling, or the chimney is leaning or separating from the house. We repoint, replace damaged brick, and rebuild where the structure has failed, tying the work back into the crown and flashing. Masonry repair usually runs $500-$3,000 depending on how much of the chimney is involved, with the written estimate setting the final price.

Spalling Brick and Soft Mortar

Spalling brick is brick that’s shedding its face, usually after years of moisture cycling through the masonry. Once the face is gone, the brick keeps absorbing water faster. Repointing the joints and replacing the worst brick slows that down.

When Rebuilding Is the Right Call

If the mortar is gone through the full depth of the joint or the chimney has started to lean, rebuilding a section is safer than patching. We show you what’s failing and why a rebuild is the right repair. The camera and the photos make the decision easier to see.

Brands We Service

We work with a curated roster of professional-grade chimney brands, and we know how each one behaves once it’s been in service for a few seasons. DuraFlex flexible liner systems are our go-to for offset flues and tight runs, and we install them to the manufacturer’s specification. HeatShield resurfacing lets us restore damaged flue tile without tearing out the liner, which most sweeps can’t offer. Gelco and Famco caps and covers are fitted products, not improvised sheet-metal work, so the exclusion lasts longer than a season.

Olympia Chimney and Copperfield round out the lineup for standard cap and liner configurations, and we match the product to the flue rather than working around a generic part. If a brand isn’t the right fit for your chimney, we’ll say so and recommend the one that is. Whether you have Gelco, Olympia Chimney, Famco, Copperfield or any other make, we can help.

Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Signs You Need a Pro Right Now

  • Water stains near the chimney or on the ceiling. A stain almost always means the crown, flashing or cap has failed. Left alone it keeps feeding moisture into the masonry.
  • White staining or crumbling mortar on the outside of the chimney. That white powder is moisture working its way out of the brick, and soft mortar means the joints are losing their hold. Repointing early is a much smaller job than rebuilding later.
  • A smell of smoke or creosote in the house when you’re not burning. That usually points to a flue or damper problem and it’s worth a camera inspection before the next fire. It’s also one of the reasons carbon monoxide risk goes up.
  • Visible cracks in the flue tile or crown. A cracked flue tile lets heat and gases into the chimney structure. That’s the setup for a chimney fire, and it’s exactly what the camera inspection catches.
  • A cap that’s missing, loose or rusted out. An open flue invites birds, squirrels and rain. A replacement cap is one of the smaller repairs on this list.

Our Process, Step by Step

  1. 1
    Book the visit. You call (844) 320-4731, we answer 24/7, and we schedule a time. Fast dispatch from 7am to 7pm, Sunday through Friday. We confirm the scope on the phone so the right tools come with us.
  2. 2
    Inspect before we touch anything. We run a camera down the flue, photograph the crown, cap and flashing from the roof, and note the masonry condition. You see the footage before any recommendation is made.
  3. 3
    Write down what we found. We give you a written report of the findings, with photos, and the repair options that fit. If work can safely wait, the report says so.
  4. 4
    Set the repair in manufacturer specs. Repairs use the brands we work with, installed to their specification, so the work is documented and traceable. That includes HeatShield resurfacing, DuraFlex liners and Gelco or Famco caps.
  5. 5
    Final check and sign-off. We re-inspect the repair, confirm it’s venting correctly and give you the paperwork for your records. One process, start to finish, with no separate contractor to track down.

How Much Does Chimney Repair Cost in Chico?

Chimney repair in Chico isn’t one price, because the work ranges from a cap swap to a liner rebuild. These are typical ranges, and the written estimate sets the final price on every job.

Repair Typical Range
Chimney cap installation $250-$600
Chimney cap replacement $200-$550
Chimney crown repair $400-$1,200
Chimney flashing repair $350-$900
Chimney masonry repair $500-$3,000
Chimney liner installation $2,500-$6,500

The biggest drivers are flue height, whether the flue is offset, how much masonry is affected, and whether the repair requires a full liner or HeatShield resurfacing. A single cracked crown is a different job from a chimney that’s lost the back half of its brick. We inspect with a camera and give you the findings in writing before quoting, so you’re not paying for a recommendation you can’t verify.

Nothing is recommended without camera evidence you can see for yourself. If the crown is cracked but the flue is sound, we tell you the crown and nothing more. If the flue is damaged but the work can safely wait until after the season, we say so and put it in the report. A free estimate includes the inspection findings and the written range for each repair option. If you’d like to compare this against routine cleaning, see chimney sweep service.

Our Service Area Near Chico

We serve Chico and the surrounding towns, including Durham, Paradise, Magalia, Orland, Thermalito, Corning, Oroville, South Oroville and Kelly Ridge. Scheduling is by appointment, and most visits in the Chico area are booked quickly. If you’re outside the immediate area, call and we’ll confirm scheduling. For nearby work, see chimney repair in Durham, chimney repair in Paradise, or chimney repair in Chico.

Serving Chico, CA – Our Local Coverage Area

We serve Chico and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.

Frequently Asked Questions About Chimney Repair in Chico

Schedule Your Chimney Repair Service in Chico Today

If something on your chimney has been put off for a season too many, book the visit and get it documented before the burning season. Call (844) 320-4731 for a free estimate, and we’ll inspect, photograph and quote the repair in writing. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.

Written by the team at Chimney Sweep Chico.

Why Chico Chooses Chimney Sweep Chico

We set the standard for chimney repair in Chico.

Evidence Before Recommendations

Every sweep includes a camera inspection and a photo report. If we find something, you see it before we quote it - no repair is ever recommended on our word alone.

Licensed & Insured

Fully certified technicians who meet all local and state licensing requirements.

Upfront Pricing

No hidden fees, no surprises. You approve the price before any work begins.

Guaranteed Work

Every repair and installation is backed by our workmanship warranty and satisfaction guarantee.

How It Works in Chico

Getting your chimney repair handled is simple and fast.

1

Call or Request a Free Estimate

Tell us about your chimney repair needs and we provide an upfront, transparent quote with no obligation and no hidden fees.

2

We Book a Time That Works for You

A background-checked, certified technician arrives at the time we agree on.

3

Problem Solved, Guaranteed

We complete the job to your full satisfaction, backed by our warranty and satisfaction guarantee.

What happens when you call

  1. 1
    A real person answersNo phone trees. Talk to a local chimney repair pro.
  2. 2
    You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
  3. 3
    We come out and measureLicensed & insured, at a time that suits you. The visit and the quote are both free.
  4. 4
    You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.

What Chico Customers Say

Trusted by homeowners across Chico and surrounding areas.

★★★★★

"Crown was cracked and taking water. Repaired it rather than quoting a rebuild, which the previous company had pushed hard for."

Claudia Martinez
★★★★★

"Thorough sweep and a clear report. He was running late from the job before and arrived near the end of the window, though he did call to warn me."

Jodi Walsh
★★★★★

"Fireplace had never drawn properly since we moved in. He found the damper was only opening halfway due to a bent linkage and fixed it in ten minutes."

Amit Rao

Ready for Chimney Repair in Chico?

Call now for a free estimate, or request one below. Licensed, insured, and here with fast help in Chico.

(844) 320-4731

Request a Free Estimate in Chico

Tell us about your chimney repair needs. We'll respond within the hour.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Now
Local Service Coverage
Call Now - We Answer 24/7